0–40° Angle Drilling Jig for Woodworking | Drill Guide Kit
$39.00 USD
$78.00 USD
Product Introduction
Drill where you marked it.
Guide your handheld drill from straight down to a 40° tilt. Set the entry point, angle, and depth before the bit touches the wood.
0–40° angle control · Repeatable depth · Adjustable edge offset
🎯 Keep one crooked hole from throwing off the whole build. A bit that wanders off your pencil line can leave a joint out of alignment. A hole drilled too deep can break through a cabinet face. The Adjustable-Angle Drill Guide Kit gives you a way to control both before you start drilling.
🪵 Bring the guide to the workpiece. Use it on a tabletop that’s awkward to move, a series of matching cabinet panels, or a wooden dowel that’s hard to center by eye.
📐 Dial In the Angle You Need — Set the marked scale anywhere from 0° to 40° and tighten both handles. Use the same setting for matching angled holes across a furniture build.
🎯 Keep Your Entry Point on the Mark — Line up the base marks with your pencil crosshair. The surface-level pivot helps keep the bit aimed at the same entry point as you tilt the guide.
📏 Match the Depth and Edge Offset — Set the depth collar to limit bit travel, then use the fence and flip stops to repeat your layout across cabinet panels or furniture parts.
🪵 Find the Center on Flat or Round Wood — Reference both edges of a board with the centering buttons, or use the V-grooves to line up the guide on a round wooden dowel.
🔧 Work in Tight Corners and Across Wide Panels — Fit the low-profile knob where a full-size handle gets in the way. Add extension rods when your fence or stops need extra reach.
Product Specifications
Specification
Details
Angle
0–40° from vertical, continuously adjustable
Drill Fit
Corded or cordless handheld drill with a chuck that securely grips the guide’s hex drive shank
Bit Holder
Keyed chuck. Check that your bit shank fits.
Max. Cutting Diameter
2½ in (63.5 mm) with a compatible bit shank and sufficient clearance at the chosen angle
Position & Depth
Adjustable fence, flip stops, centering buttons, and depth stop collar
Workpiece
Softwood and hardwood with a suitable woodworking bit
Pack Sizes
1, 2, 3, 4, or 5 complete kits
Package Contents
📦 Included in Each Kit
1 × Adjustable Base with Angle Scale
1 × Sliding Chuck Assembly with Hex Drive Fitting and Chuck Key
What you’ll need: Your own compatible handheld drill and woodworking bits.
🎁 Pick Your Pack
1-Pack — 1 complete drill guide kit
2-Pack — 2 complete drill guide kits
3-Pack — 3 complete drill guide kits
4-Pack — 4 complete drill guide kits
5-Pack — 5 complete drill guide kits
Frequently Asked Questions
Will it work with my cordless drill?
Use a corded or cordless handheld drill with a chuck that securely grips the guide’s hex drive shank. Impact drivers are not recommended.
What’s the largest bit I can use?
The maximum cutting diameter is 2½ in (63.5 mm). The bit shank must fit the guide’s keyed chuck, and the cutter needs enough clearance at your chosen angle.
Can I use it for metal or concrete?
This guide is intended for woodworking. Use a guide and drill setup rated for the material when working with metal or concrete.
Can I set an angle between the marks?
Yes. The guide adjusts continuously within the 0–40° range. Use the scale as a reference and tighten both handles at your chosen setting.
Does it come with a drill or bits?
The kit includes the guide and the accessories listed above. Use your own compatible handheld drill and woodworking bits.
Can I use it for pocket-hole joinery?
Use this guide for angled joinery holes within its range. For standard pocket screws, use a dedicated pocket-hole jig with the matching stepped bit and screw setup.
Make the first hole count.
Set up once and carry the same angle, depth, and offset through your next build.