0–40° Angle Drilling Jig for Woodworking | Drill Guide Kit

$39.00 USD
$78.00 USD
Quantity

Product Introduction

Drill where you marked it.

Guide your handheld drill from straight down to a 40° tilt. Set the entry point, angle, and depth before the bit touches the wood.

0–40° angle control · Repeatable depth · Adjustable edge offset

🎯 Keep one crooked hole from throwing off the whole build. A bit that wanders off your pencil line can leave a joint out of alignment. A hole drilled too deep can break through a cabinet face. The Adjustable-Angle Drill Guide Kit gives you a way to control both before you start drilling.

🪵 Bring the guide to the workpiece. Use it on a tabletop that’s awkward to move, a series of matching cabinet panels, or a wooden dowel that’s hard to center by eye.

Choose Your Pack

Key Features

  • 📐 Dial In the Angle You Need — Set the marked scale anywhere from 0° to 40° and tighten both handles. Use the same setting for matching angled holes across a furniture build.
  • 🎯 Keep Your Entry Point on the Mark — Line up the base marks with your pencil crosshair. The surface-level pivot helps keep the bit aimed at the same entry point as you tilt the guide.
  • 📏 Match the Depth and Edge Offset — Set the depth collar to limit bit travel, then use the fence and flip stops to repeat your layout across cabinet panels or furniture parts.
  • 🪵 Find the Center on Flat or Round Wood — Reference both edges of a board with the centering buttons, or use the V-grooves to line up the guide on a round wooden dowel.
  • 🔧 Work in Tight Corners and Across Wide Panels — Fit the low-profile knob where a full-size handle gets in the way. Add extension rods when your fence or stops need extra reach.

Product Specifications

Specification Details
Angle 0–40° from vertical, continuously adjustable
Drill Fit Corded or cordless handheld drill with a chuck that securely grips the guide’s hex drive shank
Bit Holder Keyed chuck. Check that your bit shank fits.
Max. Cutting Diameter 2½ in (63.5 mm) with a compatible bit shank and sufficient clearance at the chosen angle
Position & Depth Adjustable fence, flip stops, centering buttons, and depth stop collar
Workpiece Softwood and hardwood with a suitable woodworking bit
Pack Sizes 1, 2, 3, 4, or 5 complete kits

Package Contents

📦 Included in Each Kit

  • 1 × Adjustable Base with Angle Scale
  • 1 × Sliding Chuck Assembly with Hex Drive Fitting and Chuck Key
  • 1 × Adjustable Fence with Mounting Knobs
  • 2 × Standard Guide Rods and 6 × Extension Rods
  • 2 × Flip Stops and 1 × Depth Stop Collar
  • 2 × Centering Buttons with Screws
  • 2 × Locking Handles, 1 × Low-Profile Knob, and Assembly Hardware

What you’ll need: Your own compatible handheld drill and woodworking bits.

🎁 Pick Your Pack

  • 1-Pack — 1 complete drill guide kit
  • 2-Pack — 2 complete drill guide kits
  • 3-Pack — 3 complete drill guide kits
  • 4-Pack — 4 complete drill guide kits
  • 5-Pack — 5 complete drill guide kits

Frequently Asked Questions

Will it work with my cordless drill?

Use a corded or cordless handheld drill with a chuck that securely grips the guide’s hex drive shank. Impact drivers are not recommended.

What’s the largest bit I can use?

The maximum cutting diameter is 2½ in (63.5 mm). The bit shank must fit the guide’s keyed chuck, and the cutter needs enough clearance at your chosen angle.

Can I use it for metal or concrete?

This guide is intended for woodworking. Use a guide and drill setup rated for the material when working with metal or concrete.

Can I set an angle between the marks?

Yes. The guide adjusts continuously within the 0–40° range. Use the scale as a reference and tighten both handles at your chosen setting.

Does it come with a drill or bits?

The kit includes the guide and the accessories listed above. Use your own compatible handheld drill and woodworking bits.

Can I use it for pocket-hole joinery?

Use this guide for angled joinery holes within its range. For standard pocket screws, use a dedicated pocket-hole jig with the matching stepped bit and screw setup.

Make the first hole count.

Set up once and carry the same angle, depth, and offset through your next build.

Choose Your Pack